使用中金屬分離器**問題

使用中金屬分離器**問題Safety problems in the use of metal separators

使用中金屬分離器**問題

金屬分離器主要由檢測部分和剔除部分組成,應用電磁感原理來探測金屬。所有金屬包括鐵和非鐵都有很高的探測靈敏度。鐵磁類金屬進入探測區域?qū)⒂?

響探測區域的磁力線分布，進而影響了固定范圍的磁通。非鐵磁類金屬進入探測區域?qū)a(chǎn)生渦流效應，也會使探測區域的磁場分布發生變化,當金屬雜質

通過時,會產品報警信號,輸送給剔除部分,剔除部分翻板左右擺動,來剔除含有金屬雜質的產品.從而實現金屬雜質的徹底分離.

金屬分離器使用中的**

操作和維護的**注意事項  

當本金屬分離器工作時,應將機箱蓋和電箱門關好,避免傷害危險和本機污染,延長使用壽命.所有貼在本機上的警示標識都必須清淅可見,不能以任何理由撕

除，入料口和出料口應由直徑70mm的管連接，出口管*少應有90cm長如檢測可爆炸的材料請閱讀相關法規。如進行電子電氣組件維修或氣動組件維修,

一定要切斷電源和氣源.本操作說明書應易于獲得和字跡清晰.

使用中金屬分離器**問題只允許受過培訓的技術人員操作和維修本機.

使用中金屬分離器**問題潛在的危險 

在關閉電開關后,電箱由于外接電源仍然連接而可能處于帶電狀態.

另外,由于有壓縮氣缸的存在,切斷氣源后,氣動組件仍會動作.
 

使用中金屬分離器**問題未授權

在未經本公司授權的情況下,不允許擅自進行改裝或維修工作.

不允許的操作

在的使用范圍之外的操作是不允許的

在技術參數的范圍之外的操作是不允許的.

不允許檢測腐蝕性的材料和爆炸性的材料.

使用中金屬分離器**問題使用方向

本設備主要應用于塑料工業，也可用于食品和化工行業。

本設備設計用于在垂直管線中自由下落的小團狀材料(如粉狀或粒狀),進口應連接送料斗或管線.本設備應避免被蒸氣,灰塵或類似物質包圍,因?yàn)檫@可能影響

pvc電線的絕緣性.

使用中金屬分離器**問題危險警示

在MSG3.3電箱中連接有主電源,它與外部交流電相連,因此在電箱的門內貼有危險警示。

當電源通電并且連接好氣源時,打開設備的蓋板是非常危險的, 因次在金屬分離器的內部貼有危險警示

金屬分離器的入口和出口高度都是80mm,手可以容易的碰到活門出口, 因次在金屬分離器的出料口貼有危險警示

機箱蓋可以保護操作人員不受傷害,如要打開蓋板進行維修或保養請參閱4.4

在沒有危險警示的地方可能出現的危險。

在沒有危險警示的地方，有可能有靜電或氣動組件傷手的可能。

Safety problems in the use of metal separators
The metal separator is mainly composed of the detection part and the reject part, and uses the electromagnetic induction principle to detect the metal. All metals including iron and non-iron have a high detection sensitivity. Ferromagnetic metal into the detection area will affect the magnetic field distribution of the detection area, thus affecting the fixed range of magnetic flux. Non-ferromagnetic metal into the detection area will produce eddy current effect, will also make the detection area of the magnetic field distribution changes, when the metal impurities pass, the product alarm signal, sent to the removal part, remove part of the flap swing around to remove the Metal impurities in the product to achieve a complete separation of metal impurities.
The safety of the metal separator in use
Operation and maintenance of safety precautions
When the metal separator is in operation, the cover and the door of the cabinet should be closed to avoid the risk of injury and the local pollution and prolong the service life. All warning signs affixed to the machine must be clearly visible and can not be used for any reason The tearing, inlet and outlet should be connected by a pipe with a diameter of 70 mm. The outlet tube should be at least 90 cm long. If the explosive material is to be tested, please read the relevant regulations. If the electrical and electronic components repair or pneumatic components maintenance, be sure to cut off the power and gas source. The operating instructions should be easy to obtain and writing clear.
Use of metal separator safety issues Only trained technicians are allowed to operate and service the machine.
Use of metal separator safety problems potential hazards
After closing the electrical switch, the electrical box may be in a live state due to the external power supply being connected.
In addition, due to the presence of a compressed cylinder, cut off the gas source, the pneumatic components will still move.
 The use of metal separator safety issues are not authorized
In the case without authorization by the Company, no modification or repair work is allowed.
Not allowed to operate
Operation outside of the scope of 1 is not allowed
Operation outside the scope of the technical parameters is not allowed.
It is not allowed to detect corrosive materials and explosive materials.
Use of metal separator in the use of safety direction
The equipment is mainly used in the plastics industry, can also be used for food and chemical industry.
This equipment is designed for small pellets (such as powder or granules) that are free to fall in vertical lines and the inlet should be connected to hoppers or pipelines. This equipment should be protected from steam, dust or the like as this may affect pvc Insulation of wires.
Use of metal separator safety hazard hazard warning
In the MSG3.3 power box connected to the main power supply, which is connected with the external AC, so the door in the box with a dangerous warning.
When the power supply is energized and the air supply is connected, it is very dangerous to open the cover of the device. Because of the danger warning inside the metal separator
Metal separator inlet and outlet are 80mm height, the hand can easily touch the door exit, because the metal separator in the discharge port with a dangerous warning
The cover protects the operator from damage. If you want to open the cover for repair or maintenance, please refer to section 4.4
In danger of danger where there is no danger warning.
Where there is no danger warning, there may be static or pneumatic components injury may be.